Vinyl Floor Tile Removal in 3 Steps Vinyl Floor Tile Removal in 3 Steps There may come a time when you’ll need to do a little floor tile removal. But to do this, you’ll need to know what all is involved before you begin. What follows is a 3-step process for the removal of tile. By first preparing, then removing the tile before taking off the adhesive residue, you should be able to completely remove vinyl tile from any floor. The first thing you’ll need to do, before a single piece of vinyl flooring is removed, is get prepared. Keep in mind that any vinyl flooring created before about the middle of the 1980s might contain asbestos. Asbestos can be very dangerous, and fatal in large dosages, so you certainly don’t want to mess with any of that stuff. Therefore, just to be on the safe side, have your flooring material tested for asbestos before beginning the removal process. And if you should find any asbestos material, have it removed professionally. But in cases where you don’t even believe there is asbestos present, be extra cautious and wear a mask or respirator whenever you take out flooring, if for nothing else, to avoid inhaling too much airborne particles or dust.

Another significant preparation step is to make sure your work area is sufficiently ventilated. You can accomplish this task by opening windows and/or doors and placing fans nearby, if needed. Step 2: Take Out the Flooring Be prepared to feel a little pain the next day because removing vinyl tile applied with self adhesive is hard work. You’ll need to put in a lot of physical labor, and have a little more than the usual amount of patience. The most efficient and effective method for removing tiles requires heat and a tough scraper. If you put heat on the tile, the underpinning adhesive loosens up and doesn’t bind so tightly with the floor. Sometimes, all you need for this heat is a typical hair dryer. But if that doesn’t do the trick, try an electric heat gun. Another safety precaution involves handling a heat gun with care; these create high temperatures, which can burn you and your floor. Step 3: Take Out the Adhesive Once you have taken out every tile, you will still have remnants of adhesive residue.

There might be a lot, or there may be just a little. In some cases, vinyl installers apply added spread adhesive when they do their work, and this compounds the residue factor even more. Fishing Rod Racks For BoatsKeep in mind that if you’re attempting to preserve the flooring beneath your vinyl, there is a chance of damaging it during the adhesive removal process. Rope Lights For FountainsTherefore, there is an amount of risk involved. Cheap Bird Bath MelbourneMethods of residue removal involve scrubbing this stubborn stuff with mineral spirits, as well as making it softer using steam or hot water. Best of all, however, is to purchase flooring adhesive remover at your local hardware outlet. These products work by laying on a chemical product, which then sits for a while to make the adhesive soft, and then the residue can be scraped off.

Vinyl Floor Tile Removal: 3 TipsSkip to main contenteBayShop by categoryEnter your search keywordIndustrial Heat Guns└Light Industrial Equipment and Tools└Business & IndustrialAll CategoriesAntiquesArtBabyBooksBusiness & IndustrialCameras & PhotoCell Phones & AccessoriesClothing, Shoes & AccessoriesCoins & Paper MoneyCollectiblesComputers/Tablets & NetworkingConsumer ElectronicsCraftsDolls & BearsDVDs & MoviesEntertainment MemorabiliaGift Cards & CouponsHealth & BeautyHome & GardenJewelry & WatchesMusicMusical Instruments & GearPet SuppliesPottery & GlassReal EstateSpecialty ServicesSporting GoodsSports Mem, Cards & Fan ShopStampsTickets & ExperiencesToys & HobbiesTravelVideo Games & ConsolesEverything ElseAdvancedDaily DealsGift CardsSellHelp & Contact see allsee all$$see allsee all2 miles5 miles10 miles15 miles20 miles50 miles75 miles100 miles150 miles200 miles500 miles750 miles1000 miles1500 miles2000 Leister Heat Gun 40MM Nozzle With Case Manual & New Seam RollerNew Heat Gun Hot Air Dual Temperature+4 Nozzles Power Tool 1500 Watt W HeatgunLeister ST 40MM Nozzle Case Seam Roller Extra Leister ElementNew Heat Gun Hot Air Gun Dual Temperature+4 Nozzles Power Tool 1500 W Heater GunLeister Ch-6060 Air Heat Gun Blower1600W Hot Air Torch Plastic Welding Gun Welder Pistol220V 1600W Hot Air Torch Plastic Welding Gun Welder Pistol With Rollder BrushLEISTER CH-6060 TRIAC S HEAT GUN PLASTIC

WELDERSteinel 31331 Hipurformer Advanced Bonding System Glue GunNew Leister 100.702 120V 1600W Heating Element Triac SMaster Appliance® HAS-011K Heating Element (replacement for HG-501A Heat Gun)BRAND NEW PRO 1500 Watt Dual Temperature Heat Gun (600°/1000°) HEAT GUNMilwaukee 8977-20 11.6 Amp Variable Temperature Heat GunGot one to sell? No. 970 Power Groover This groover has seam tracking wheels that follow the seamline to cut a trapezoidal groove for welding. It has a simple visual depth control knob that is labeled in increments of 1/10 of a millimeter. Chips are more effectively collected in the dust bag due to optimized direction of airflow within the housing. Comes with a 12 tooth 130 mm carbide tipped blade that is replaceable and resharpenable (No. 971), and a metal carrying case. A heavy grit diamond blade for metal-impregnated safety floor is available as an accessory (No. 972). Motor specifications: 110V AC 9A No Load RPM 12,000. Maximum cutting depth: 4mm. No. 971 12 Tooth Carbide Blade

This is a replacement carbide tipped blade for the Crain No. 970 Power Groover. It is a 12 tooth 130 mm diameter blade which can also be used on other groovers that take this size blade. It cuts a trapezoidal shaped groove in the material. It is not for use on metal impregnated safety floors. This blade is resharpenable. For safety floors, see the No. 972 Diamond Groover Blade. Net weight: 8 oz. No. 972 Diamond Groover Blade This is a heavy grit diamond abrasive cutting blade for metal impregnated safety floors. It has continuous diamond grit brazed on its entire outside diameter. Its 130 mm diameter works on other groovers that take this size blade. It produces an approximately 3.4 mm wide groove. Diamond wear affects width and depth of cut. Net weight 1 lb. 1 oz. No. 969 Heat Weld Gun This heat welding gun comes with a Leister Triac ST heat gun for consistent and reliable heat output. A single dial on the back controls output temperature from 104° - 1290°F. The standard 11/4" outlet fits a variety of nozzles.

Also includes a pencil tip nozzle (No. 963), triangular speed welding tip for triangular or "half moon" rod (No. 961), round speed welding tip for round rod (No. 962), and carrying case. Net weight: 7 lbs. No. 960 Heat Weld Gun This heat welding gun has electronic temperature and airflow control that is continuously adjustable using separate sliding controls. Produces hot air from 80°F to 1250°F and variable airflow up to 15.4 CFM. The gun comes with a precise fitting pencil tip nozzle, a triangular speed welding tip for triangular or "half-moon" welding rod, and a round speed welding tip for round rod. The tips have hot air outlets that are precision formed to focus heat over the seam area and minimize scorching. Comes with detailed instructions for heat welding seams. Net weight: 3 lbs. No. 961 Triangular Welding Tip This triangular speed welding tip for the Crain No. 960 Heat Weld Gun is for welding seams using triangular or "half-moon" ("half-round') welding rod.

The air outlet is precisely formed to focus hot air over the seam area and minimize scorching. This tip has a standard sized inlet diameter that fits the pencil tip nozzle outlet of most other popular heat weld guns. Net weight: 1 oz. No. 962 Round Welding Tip This round speed tip for the Crain No. 960 Heat Weld Gun is for welding seams using round 4 mm welding rod. No. 979 Universal Welding Tip This versatile tip works with 3 mm or 5 mm round welding rod, "half-moon" ("half-round") welding rod, or triangular welding rod. It has an adjusting screw at the rod inlet to adapt the inlet to the various rod shapes. The grooved brass pressure roller is also adaptable to the various rod shapes. The hot air inlet is sized to fit the Crain No. 960 Heat Weld Gun or previous model No. 980 Heat Weld Gun, as well as other popular models of heat weld guns. Net weight: 4 oz. No. 963 Pencil-Tip Nozzle The pencil tip nozzle adapts our No. 960 Heat Weld Gun to our No. 961 Triangular Welding Tip, No. 962 Round Welding Tip, No. 963 Pencil-Tip Nozzle, or No. 979 Universal Welding Tip.

The angled outlet is convenient for holding the heat gun and keeping the speed tip in contact with the welding rod. This nozzle is also for welding coved areas in conjunction with a pressure roller (No. 967). This nozzle has a standard diameter inlet that fits most popular heat weld guns, and a standard diameter outlet that fits most popular speed tips. Net weight: 3 oz. No. 955 Pull Hand Groover This hand groover cuts a U-shaped groove at the seam line for welding. It used for starter grooves near the wall for insertion of a power groover, for making grooves in tight areas like doorways, or wherever floors are not level. It is designed to groove by pulling on the large wooden handle. The adjustable fin guides the U-shaped blade along the seam line and controls the grooving depth. The depth control prevents gouging and rising up of the blade. The result is a uniform groove at a faster rate. Comes with 3 blades, one pre-loaded on the tool, and two stored in the handle. Net weight: 6 oz.

No. 956 Pull Hand Groover Blades (3) These U-shaped replacement blades for the No. 955 Pull Hand Groover come in a pack of three each. They are precision formed from high carbon steel, heat-treated, and hand sharpened. The locator hole above the screw hole keeps the blade rigidly in place on the blade holder of the Crain No. 955 Pull Hand Groover. The standard shape of this blade allows it to be used on other popular pull hand groovers as well. Net weight: 1/2 oz. / pack. No. 985 Quarter Moon Knife This knife is used to trim excess welding rod from the seam area after cooling to make the seam area flush with the rest of the floor. It is used in a two-step process in conjunction with the No. 986 Trim Guide. First, insert the trim guide beneath the knife and trim off the bulk of the material on a first pass. Afterwards, remove the trim guide and make a second pass with the knife only. The fine cut of the second pass finishes flush with the surrounding floor. The knife comes with a protective pouch.

Trim guide not included. Net weight: 2 oz. No. 986 Trim Guide This steel depth control guide is used with the No. 985 Quarter Moon Knife in a two-step trimming process that removes excess welding rod from the seam area after cooling. Afterwards, the trim guide is removed and a second pass is made with the knife only. No knife is included with this guide. No. 988 Vinyl Welding Kit This kit includes the basic tools needed for vinyl welding, all at a great price! It includes: No. 969 Head Weld Gun (including a Leister Triac ST heat gun, No. 963 Pencil Tip Nozzle, No. 961 Triangular Welding Tip, and the No. 962 Round Welding Tip), No. 970 Power Groover, No. 955 Pull Hand Groover, No. 985 Quarter Moon Knife, and No. 986 Trim Guide. Comes complete with a metal carrying case that holds all the tools in the kit. No. 965 Skiving Knife w/Blade This knife for trimming excess heat welding rod at the seam comes with a sharp, flexible blade that is replaceable and a built-in pivoting trim guide, all in one tool.

Eliminates difficult resharpening and gouging problems with quarter moon knives. Uses a two-step process for trimming. On the first pass, trim with the guide under the blade to remove the bulk of the material, then pivot the trim guide out of the way on the second pass. The flexible blade won't gouge high spots. Net weight: 7 oz. No. 966 Skiving Knife Repl. Blade Includes one each replacement blade for the No. 965 Skiving Knife used for trimming excess heat welding rod flush at the seam. This replaceable blade is flexible to eliminate gouging high spots which can occur with quarter moon knives. It also eliminates difficult resharpening of quarter moon knives. Net weight: 1/4 oz. No. 967 Skiving Knife Repl. Blades (5) Includes a pack of five replacement blades for the No. 965 Skiving Knife used for trimming excess heat welding rod flush at the seam. These replaceable blades are flexible to eliminate gouging of high spots which can occur with quarter moon knives. They also eliminate difficult resharpening of quarter moon knives.