When something's not working, you need it fixed fast. You can either call a professional or attempt to fix it yourself. With American’s Standard's Care & Repair tools, you can diagnose your own situation to help you get quickly on your way. To start, identify what type of product you have from the list below. How to Stop Your Bathroom Faucet From Dripping How to Stop Your Bathroom Faucet From Dripping A simple bathroom faucet repair can save you money and benefit the environment as well. Since a leaking faucet wastes more water than you may realize, a quick repair is important. Follow these easy steps to fix your leaking bathroom faucet. There are two standard faucet types: compression faucets and washerless faucets. Compression faucets are the older, two handle style. Washerless faucets use a single handle or lever to control water flow. They may be disc, ball, valve, or cartridge faucets. Before beginning the bathroom faucet repair, plug the sink so that you won’t lose any parts.

Tape the wrenches you’ll be using so that you don’t mar the surface of any fixtures when you take them apart. Make sure to keep track of any pieces and take them with you to the hardware or home improvement store. There are many different kinds of faucets. Auto Repair AnimationYou need to get the exact replacement types. Car Seat Bottom Cushion CoverClose the water shutoff valve.Laptop Power Button Light Flashing Generally speaking, the leaking compression faucet handle is a result of a corroded “O” ring, rubber gasket, twine, or the packing nut that holds the packing. A leaking spout is usually the result of a leaking washer or valve seat. While the faucet is apart, replace them. A valve faucet could be leaking as the result of a corroded “O” ring, bad cartridge, or seals.

Handy Duct Tape Uses Around the House Single Handle Kit-Bath-T/S-47MM Cartridge 2-Handle Kit and Bath Cartridge Single Handle Kit/Bath 40 MM Cartridge Valve Cartridge Kit for Metering 023529-0070A Cartridge Kit with Seals Seal Kit for Cartridge A951470 40MM 066269-0070A Ultramix Cartridge with Screws Actuating Unit for Metering Faucet, Polished Chrome Cartridge for Lavatory and Kitchen Faucets 006080-0040NL Renu Lavatory Left Hand Stem 2 or 3-Way In-Wall Diverter Stem Kit Lakeland Internal Body and Seal 072951-1700 AquaSeal Left Hand Stem Valve Cartridge for Metering Faucet Hampton Valve Escutcheon Kit, Satin Nickel Aquaseal S/A-L/H Stainless Steel Locknut 15 mm Eco-Cartridge for Hot or Cold Cartridge Kit - Hot Side I just installed a new tub fixture set: There are two controls - one for temperature and one for volume. The large handle is volume. When the diverter valve is engaged the shower sprays properly and no water comes from the spout:

But if I disengage the diverter and run the water at full pressure, the spout flows but there is still a slow shower from the shower head: However, if I reduce volume enough: (note the angle of the volume control) the shower stops dripping: Is something wrong with my installation, or am I right in suspecting that I simply have too much water pressure in my house? I've checked all the plumbing from behind (the wall behind the tub is open) - there are no leaks. plumbing shower bathtub water-pressure plumbing-fixture What did you use to connect your tub spout? I plumbed my bathroom with Pex and was heavily cautioned NOT to use Pex to run from the main valve to the tub spout because it would create exactly the issue your describing. Since the inner diameter of Pex is slightly less than regular copper (or threaded brass fittings, which is what I used) it will create a slight flow restriction to the tub spout and (inadvertently) divert it to the shower head.

It seems to me that it boils down to the basics... you have a certain volume of water at a certain pressure. If the diverter is fully open, and there is more water coming through than it can handle, then there is overflow going to the shower. The water pressure can't be more than what is available coming in, so that should be regulated for the whole house; if it's too high, valves could fail elsewhere. If it's correct, then this can't really be the problem (directly). So, it must be a matter of pipe sizes or diverter valve capacity. There must either be an obstruction at or after the diverter valve, or the pipe going to the shower is too small and fills up, so to speak. If the pipe going to the shower head was bigger, it would act as a reservoir and take more water before it overflows out the shower head. It may be that there is simply too much water coming to the shower, and a flow restrictor leading to the valves, or limiter on the valves is needed. I don't know if the valves have a way to limit the water.

The main question would be whether there is lots of water coming out of both the shower head and the tub outlet when the valve is at the setting that does not come out of the shower head when it shouldn't. Sorry this isn't exactly a full answer, but it's too much to put in a comment, and I thought it might be helpful for troubleshooting the problem. The volume of water to the tub spout can be too high creating back pressure which leads to water dripping or pouring out of the shower head. To solve this, try using 1/2" brass pipe fittings from the control to the tub spout only. This increased diameter of pipe will allow full flow and prevent any back pressure. I have done this numerous times on all types of controls and it works every time. Decreasing the water pressure at the valve can, and likely will, cause frustration because of the noticeable lack of pressure. I had the same problem today and after looking into the pipe connection in the wall that connects the faucet, I noticed that a rubber gasket on the 90 degree elbow was damaged and was prohibiting the proper flow of water.