A small gap is normal and necessary to allow proper movement of the handle without damaging the escutcheon below it. An excessive gap results from improper height adjustment at the time of installation. Loosen the nut under the counter/sink. Then screw the escutcheon UP just enough to make up the gap. Then re-tighten the nut. This lowers the valve and reduces the gap Was this answer helpful? In most cases, the finish is safe if you follow the manufacturer’s instructions for use and make sure the drain cleaner isn’t left on the finish for longer than 30 minutes. Remove the aerator, soak it in vinegar overnight, then flush with water. For stubborn deposits, rub with a toothbrush. Always blot dry any water from the faucet surface. Allowing water to evaporate on the surface can lead to build up of mineral deposits. Cleaning with a damp non-abrasive sponge and buffing it dry with a clean soft cloth should help keep your product looking beautiful. To remove water spots, use warm water and a soft, damp cloth.

Hard water stains may be removed using a 50/50 solution of white vinegar and water.  Make certain that you rinse the surface thoroughly with water afterward. If additional cleaning is required, all of our finishes may be cleaned with the following household cleaners: Formula 409® Antibacterial All Purpose Cleaner, Fantastik® All Purpose Cleaner, or Windex Original Glass Cleaner, when used according to the manufacturers' instructions for use. Avoid using the following which can damage your finish: Avoid industrial cleaners and abrasive cleaners, such as those used for toilet bowls, green Scotch-Brite heavy duty scrub sponges, Scrubbing Bubbles Bathroom Cleaner and Lysol Basin Tub, Soft Scrub, and Tile Cleaner. Avoid products that state on the label that they remove tarnish and rust and those containing hydrofluoric, hydrochloric and/or phosphoric acids and caustic agents. Avoid harsh abrasives or polishes. Always blot dry any water from faucet surface. Make certain that you rinse thoroughly with water afterward.

If additional cleaning is required, all of our finishes may be cleaned with the following household cleaners: Formula 409® Antibacterial All Purpose Cleaner, Fantastik® All Purpose Cleaner, or Windex® Original Glass Cleaner, when used according to the manufacturers' instructions for use. Avoid products that state on the label that they remove tarnish and rust, and those containing hydrofluoric, hydrochloric and/or phosphoric acids and caustic agents. Avoid harsh abrasives or polishes Some common tools include: Silicone sealant - Plumber's Putty is not generally recommended Screwdriver (Phillips and slotted) Please refer to the Maintenance & Installation Sheet supplied with the faucet to make sure you have all the necessary tools. If you need a Maintenance & Installation Sheet for your faucet, visit the Online Catalog and search for your faucet. When your faucet appears, select the Maintenance & Installation option to view the installation information.

Call us at 1-800-345-DELTA (3358), Monday through Saturday, 7 a.m. to 9 p.m. CST or Click here to send a message directly to Customer Service.Party Furniture Rental Sacramento Soaking your aerator in white vinegar overnight should help remove any mineral deposits and normal build up. Light Bulb Effect CandleAny extra-stubborn deposits can be broken free with a tooth brush. Battery Operated Lights For Wedding CenterpiecesOnce complete, simply rinse the aerator off with water. Delta Faucet Company recommends you leave the existing fitting on the PEX supply tubing and not shorten the tubing. If you determine the PEX supply tubing for this faucet is too long and must be shorter to create an acceptable installation, be sure to read the instructions and plan ahead.

When cutting the supply tubing, the installer accepts the responsibility to do so in a way that allows a leak-free joint to be created.  Delta is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. For custom fit installations, you must use RP50952 sleeves supplied with model and nuts included on supply lines. Tube cut must be straight. See plastic sleeve installation instructions found on RP50952. NOTICE: DO NOT use a metal sleeve, RP51243 gasket (supplied with faucet) or ferrule in the place of the plastic sleeve supplied--it may not create a leak-free joint. Do not use pipe dope or other sealants on water line connections. Instructions: Watch this how-to video for information on how to cut your PEX supply lines to size. 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation, and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube.

Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4). Tube should touch bottom of hole inside fitting. 4. Slide plastic sleeve down tube until it engages top of fitting. NOTICE: Failure to use plastic sleeve in the correct orientation will result in disconnection and possible water damage. 5. Slide nut over plastic sleeve. With wrench, tighten nut 2 turns past finger tight.  Yes, you just need to be cautious not to scratch or bend the part. How To Retrieve Jewelry from a Drain Most expensive, most affordable places in Md., Va. Listing service Coldwell Banker is out with its annual report on the most expensive and affordable homes in the real estate market for four-bedroom, two-bathroom homes across the United States. Weekend Best Bets: Fun events around the DC area 9/11 Memorial Stair Climb honors national, local firefighters Five foods to slash your diabetes risk The Onion ramps up speed of satire in Campaign 2016