Posi-Temp Pressure Balanced Shower Cartridge Cartridge for Moen Posi-Temp 17 Series Monitor Tub and Shower Cartridge MO-9 Cartridge for Moen Posi-Temp Single-Handle Faucets Mixet MXT07 4-1/2 in. Hot/Cold Post-1968 Stem with Retainer Hot/Cold Brass Stem Assembly for Faucets Cartridge for MOEN Posi-Temp Replacement Cartridge for Delta Monitor Faucet PP-45CD-NL Hot and Cold Stem for Price Pfister Brass Cartridge for Moen Universal OX8 Pressure Balance Cartridge for 974-042 Ceramic Disc Cartridge for Tub/Shower Faucet Plastic Cartridge for MOEN 11B-1 Hot/Cold Stem for Gerber Tub and Shower Faucets PP-493 Hot and Cold Stem for Price Pfister 910-374 Marque Hot and Cold Replacement Stem and Bonnet S74-292 Avante Hot and Cold Replacement Cartridge for Tub and Shower Tub and shower faucets work much like sink faucets, but they are oriented horizontally rather than vertically and their parts are usually larger.

A two-handle stem shower faucet has a stem with a washer that presses against a seat to seal off water. A three-handle unit adds a stemlike diverter to direct water up to the shower or down to the tub spout. Often leaks can be fixed simply by replacing the washers. Even if you need to replace the seats or stems, it's easier to repair than to replace an old shower faucet, because replacement requires opening the wall. If parts are hard to find, order them at a plumbing-supplies store. An hour or two for most repairs Screwdrivers, handle puller if needed, adjustable wrench or groove-joint pliers, stem wrench or seat wrench if needed Shutting off water, dismantling a faucet, installing small parts Shut off the water, close the tub stopper, and place a rag in the tub to catch any loose parts Washers, O-rings, seats, new stems if needed Shut off the water. Turn on the faucet until the water stops running. To remove the handle pry off the decorative cap and remove the screw, using a hex wrench or screwdriver as needed.

Lift off the handle. If the stem protrudes far enough past the wall surface, loosen it with an adjustable wrench or groove-joint pliers. For a recessed stem, use a stem wrench. If water seeps out around the handle, replace a worn packing washer or stuff thread packing around the stem and into the cavity behind the packing nut. If water drips out the spout or the showerhead, replace a worn washer with a new one that is exactly the same. If replacing the washer does not stop the leak or if washers wear out quickly, remove the seat with a seat wrench and replace it. Licensed T Shirts WholesaleOr grind the seat smooth with a seat grinder.Russian Blue Cat For Sale Nc Replacement shower faucet stemMiniature Puppies For Sale In Houston Tx

If you find that your shower faucet stem leaks regularly when you are taking a shower, or if the parts of the stem have begun to wear down through regular use, then you will need to install a new one. Replacing a shower faucet stem is not a very difficult task, and rather than call a plumber, you should be able to perform this simple task completely on your own. In order to get the best from your installation, you will need a few basic household tools, and some free time in which to complete the project. Performing this simple replacement will help save you money, and stop your shower leaking. Before you begin any project in your bathroom, it is always a good idea to turn your water off at the mains. You might consider just shutting off the water to your shower, which will allow you to run water to other parts of the house, but this is often a false saving, and will leave you vulnerable to water leaks. Turn off the water supply using your key, or by twisting the valve using your wrench.

Run the water in your bathroom a little in order to ensure that the faucet is completely empty before you work on it. At the top of your faucet handle, you will be able to see a round disc. This is the cover for your faucet, and can be removed using the flat tip of your screwdriver. Once this has been popped off, you should be able to see a large screw which is holding on your shower handle. Undo this screw, and place it to one side. Take off the handle. You should be able to see a flange behind the handle. This also needs to be removed. Now you will be able to see the stem. On each side of the stem is an old bolt, shaped like a hexagon. You need to look at the bolt which is closer to the wall. Using a wrench, simply loosen this, and then remove it. You can then take off the stem. You may sometimes find that the bolt is actually fitted into the wall, in a recess, in which case you will need to unscrew it using a socket wrench. Once the bolt is free, the old stem can be taken off.

Take your new shower faucet stem, and make sure that the one is a suitable match for the other. You need a perfect stem double in order to prevent leaks. Push the new stem onto the wall, and tighten the bolt back up. Replace the flange, and then reattach the handle using your screwdriver. When this has been done, you can then refit the cover.How to Repair a Tub & Shower Valve If the faucet valve for your tub and shower malfunctions, use the steps here to make the repair. Packing nut washer (optional) Step 1 Turn off water Turn off the water to the bathtub and shower at the shut-off valve. Let any remaining water flow out of the faucet. Step 2 Remove the cap and screw Remove the cap and screw from the faucet handle using a screwdriver, and take off the handle and escutcheon. Step 3 Remove stop tube and cartridge Remove the stop tube and cartridge with pliers if you have a washerless faucet. Washerless faucets use a single knob to control hot and cold water. Make a sketch of how parts fit together as you disassemble them.