Pro Pull Bar for Laminate and Wood Floors Great for laminate and wood flooring installation, the ROBERTS 3 in. Pro Pull Bar helps you reduce seams in tight spaces, such as against a wall, that can't be reached with a tapping block. The bar features durable steel construction. Use to gently pull together planks of tongue-and-groove, laminate or wood flooring Ideal for use in tight spaces, such as against a wall For use with a mallet This question is from Pro Pull Bar for Laminate and Wood Floors8 Is the bar necessary for t&g glue down cork flooring? This question is from Pro Pull Bar for Laminate and Wood Floors4 How long is the toolLooking to add that special touch in your home? Attractive, versatile, extremely durable and appropriate for any room, SwiftLock laminate flooring is great for any home makeover. It's available in the most popular wood finishes, and it can be installed over almost any existing flooring. You can install SwiftLock flooring with just a few basic tools.

Plan to take your time on this project: Set aside a weekend and recruit a helper.Pry BarHammerCircular SawKnee PadsSwiftLock FlooringFloor LevelerUnderlaymentRagsMouldingsInstallation Kit1/4-in. Patio Chaise Lounge Towel Cover SetSpacersSwiftLock Floor SystemsUnlike traditional wood floors, SwiftLock laminate floors are installed as floating floors that aren't physically attached to the subfloor by nails, screws or pegs.Pale Yellow Shower CurtainsThe floorboards simply lock together. Car Seat Upholstery CourseExpansion areas (concealed by wall base trim) are left along the perimeters of the finished floor, allowing the flooring to expand and contract with temperature and humidity changes.Where to InstallSwiftLock laminate flooring is appropriate for any room and can be installed over ceramic tile, concrete, well-bonded vinyl or board / ply underlayments.

It can even be installed over short pile carpet that's less than ¼ inch high and has no pad underneath.SwiftLock can be installed in the bathroom if you take certain precautions. For bathroom installation, apply a thin bead of laminate floor glue along the top of the tongue and a bead of silicone caulk in the expansion gap around the perimeter of the floor.Preparing Your Flooring for InstallationFollow these steps to get the subfloor ready for installation:Step 1Remove any existing wall base or trim.Step 2Ensure that the subfloor is clean, dry and level before proceeding.Step 3Roll out foam underlayment, which will provide soundproofing and make the floor more comfortable for walking. Don't overlap at the edges. Cut to fit the room, and install according to the manufacturer's instructions.Step 4If the flooring won't slide under the door casing, mark the casing 1/16 inch above the flooring. Cut the door casing at the mark with a coping saw or back saw.Step 5Check to see if the doors clear the new flooring.

If a door doesn't clear the new flooring, mark it 1/8 inch above the floor. Take the door down, and plane or cut it to the mark.Step 6Butt a piece of flooring against the wall, where you intend to start laying the floor. Tightly butt small pieces of flooring together across the room. In most cases, there will be a space between the wall and the last piece of flooring. Subtract twice the expansion gap from the space, and add that number to the width of the flooring. Divide the sum in half to determine the width you need to cut the first row of flooring.Example:The expansion gap is 1/4 inch, the space between the last board and the wall is 3 inches and the flooring is 4 inches wide.2 x 1/4"= 1/2"3" - 1/2"= 2 1/2"6 1/2" / 2 = 3 1/4"Rip-saw the first row of flooring to 3 1/4 inches. Use this technique to avoid having a narrow strip of flooring in the last row. When using a power saw to cut the flooring, turn it finished side down. When using a hand saw to cut the flooring, turn it finished side up.

Step 7Establish a baseline to make up for slight imperfections in the room. Mark the center of each wall, and snap chalk lines between the opposing marks. The point where the lines intersect is the center of the room. The line running parallel to the flooring is the base line.Step 8Measure from the center point to the wall where you intend to start the flooring. Subtract the expansion gap from this distance.Example:The distance from the center point to the wall is 106 1/2 inches, and the expansion gap is 1/4 inch.106 1/2 - 1/4" = 106 1/4"Measure from each end of the base line toward the wall 106 1/4 inches and snap a chalk line between the marks. The new line is the guideline.Installing Your Laminate FloorsStep 1Inspect each piece of flooring prior to installation. Remove any damaged pieces.Step 2Cut the tongue off of the first row of flooring.Step 3Starting along one wall, lay out the first row of flooring with the tongue side against the guideline.Step 4Install 1/4-inch spacers between the flooring strip and the wall.

The spacers establish the expansion area to allow for floor movement. This gap will be covered later with wall base moulding.If the starting wall is crooked, scribe the contour of the wall on the flooring. Cut along this line to produce a board that conforms to the wall contour.Step 5Working from left to right, begin to lay the flooring pieces. Slide each piece to the left, and lock the short end into place. Carefully tap the short ends of the boards to connect them.Step 6When you reach the wall, cut the last piece long enough to fit, while maintaining a 1/4-inch expansion area at each side wall. As the floor is installed, maintain the 1/4-inch expansion area around the entire perimeter of the floor.If you're using a hand saw, cut the flooring with the finish side up. If you're using a power saw, cut the flooring with the finish side down. This technique should minimize the possibility of damaging the finish during the cut.Step 7Put the last piece in place with a pry bar, with 1/4-inch spacers at each end of the row.

Step 8Leave a 12-inch-minimum overlap between end joints. If the piece left is over 12 inches long, it may be used to begin the next row of flooring. If it's less than 12 inches long, cut a full board in half and use it to start the next row. Always keep a minimum of 12 inches of overlap between the end joints in adjoining rows of boards. Use the pry bar to tighten up the joints.Step 9Continue laying boards one row at a time, locking them into place as you go.Step 10Use spacers to maintain your 1/4-inch expansion space along the walls.Finishing TouchesStep 1Use transition mouldings as necessary. End mouldings, T-mouldings and reducer strips are available to make decorative and functional transitions where the new flooring meets existing flooring. (Predrill all mouldings and transition strips before nailing or screwing.)Step 2Install base mouldings along the wall perimeter to hide the expansion area and provide a decorative, finished appearance.Step 3Don't fasten flooring to the subfloor.