At least 48 hours prior to installation, place the new vinyl plank flooring in the room for acclimation. During installation, mix planks from different boxes to blend the dye lots and patterns for a more uniform appearance. Good to KnowYou may install vinyl over vinyl if the existing floor is one layer thick. Prep your subfloor so that it is clean, dry and level within 3/16-inch change per 10 feet. Use a self-leveler on low spots and / or sand high spots of wood or concrete. Do not sand vinyl flooring – it may contain asbestos. Self-leveler is available in powder and pre-mixed form and is used to create a flat, smooth surface in flooring projects. The strength of the product is similar to concrete. Self-leveler dries quickly, so work quickly. Keep in mind that some walls are bowed, so it’s important to create a starting line square to the room. Mark the center of each wall and snap lines between them with a chalk line. Measure from the center to the starting wall, subtracting the 5/16-inch expansion gap, and mark this distance at each end of the wall.

Snap a chalk line between these two marks to get a straight line against the wall. Finally, calculate the width of the last row. If it will be less than 1/3 of a plank, cut about 1/3 of the plank off the first row for even starting and finishing rows. Score and cut the tongue off the first row of vinyl planks using a utility knife. Set the first plank in place on the starting line with the cut side toward the wall, maintaining the expansion gap. Hold the next plank at a slight angle against the previous plank's end and fold down to click it into place.Names For Male Stray Cats Good to KnowThe end piece must be at least 6 inches long. Ford Mustang Gt T ShirtsIf it’s not, cut a bit off the first plank and slide the row.Tom Brady T Shirt Funny

To cut the last piece to fit, score with a utility knife and snap the plank. Good to KnowYou can use excess cut pieces to start rows if the pieces are at least 6 inches long. The Second Row Onward The joints must be staggered at least 6 inches. Measure and cut your first piece accordingly, using a cut end from the first row if necessary. Insert the tongue of the first piece into the groove of the previous row's first plank and rotate down to click together. For the next piece, connect the short end first and then connect the long end. You should feel it lock. Continue the installation, making sure to stagger the joints by 6 inches and maintain the expansion gap. To get under doorjambs, slightly bend the planks into place and use a pull bar or tapping block to lock the joint if necessary. Peel-and-Stick Vinyl Plank Flooring The floor preparation and layout are the same for peel-and-stick vinyl planks as they are for floating vinyl plank floors.

To install each piece, peel the adhesive backing off of the plank and stick it to the subfloor. Replace the baseboards and add transitions and additional trim pieces, like shoe-moulding, if desired. Be sure to nail the trim pieces to the wall, not the floor.A natural neutral, bamboo’s striated pattern and low-key colors work in any decorating style, especially when you’re trying to achieve a relaxed, minimalist look. Luxury vinyl bamboo flooring is a beautiful solution for introducing bamboo’s soothing tranquility and casual elegance to any room in your home. also ideal for rooms where traditional bamboo flooring isn’t recommended. Get the Bamboo Look in a Waterproof Floor Luxury vinyl bamboo flooring is waterproof and can be installed in any room where moisture is frequently present. the unique look of bamboo flooring creates a spa-like ambiance where you’ll love to relax. In basements, you can design a peaceful retreat for family and friends.

In kitchens and laundry rooms, too, you’ll enjoy the serene look of bamboo flooring while never having to worry about warping, stains or water damage over time. Plus, vinyl plank flooring is exceptionally durable and highly resistant to scratches and daily wear and tear. Decorating a room with luxury vinyl plank bamboo flooring is smart. It’s beautiful, affordable flooring that won’t strainWhen it comes to installation, you can easily do it yourself. All that’s needed to complete a whole new floor are a few common household tools. When you find something so inspiring and naturally attractive, you want to surround yourself in its comforting atmosphere. Bamboo flooring in luxury vinyl plank brings the artistry of natural simplicity into your home.Installing hardwood flooring can be a cinch, or it can be a nightmare, depending on the sub-floor you are working with and the pattern you want to create. Do you do it yourself or hire it done? There are three general methods installing hardwood flooring in your home.

When it comes to choosing the best installation method, your sub-flooring should be taken into consideration to narrow down your installation options. If you have plywood sub-floors you can choose any installation method, but if your sub-floors are concrete, floating or gluing are advised. One trick of having a professional looking job is to start at a focal point, like a fireplace hearth and work from there. Once you establish your starting point, snap a chalk line so you have a straight reference point. You can install wood flooring on concrete with proper care. Installing hardwood on top of vinyl or linoleum flooring may not take any preparation, other than starting with a clean surface. Installing hardwood flooring to carpet will often require a reducer strip to account for the different thicknesses. Patterns for wood floor installations can be lots of fun. You could consider installing herringbone hardwood flooring pattern. Or think about a diamond shape. Maybe using different colors of wood can create a pattern like a throw rug with one color of wood acting as the border around the simulated rug.

There are so many ways you can create interest with your hardwood floor installation. Let’s look in detail at the different installation methods. The floating method of installing hardwood flooring has become very popular in recent years. Floating is a very stable installation method since it’s not attached to the sub-floor. It floats above it, allowing for the natural expansion and contraction of a natural product. Unlike other installation methods where each plank or strip is installed individually directly to the sub-floor, a floating installation involves gluing or clicking the boards together. This method is very common with engineered and laminate hardwood flooring. Before beginning your floating hardwood floor installation decide if you want an underlayment (made of foam, plastic, or cork) to help insulate noise transmission. If you want that muffling, then the underlayment must be put down first. The wood flooring is then laid on top of the underlayment. The glue used along the edges can be water-based or petroleum-based, and it is applied to the groove of the plank and the boards are then tapped together using what is known as a tapping block.

Excess glue is wiped off with a damp cloth. Repeat the process until the room is complete. The clicking method (or CLIC) literally involved clicking the tongue and groove edges together for each board you lay. it’s faster and cleaner because you don’t have to take the step of applying glue, and then wiping excess off the surface. The floating installation is an excellent do-it-yourself method and someone with little or no experience can get great results. You opt for a glue down installation primarily when installing an engineered strip or plank floor over a concrete sub-floor. Glue down installations can be very stable once properly installed. The glue down method can be used with plywood sub-floors, making the wood floor quieter than with either floating or staple down floors because there is less creaking. Before installing using the glue down method for your wood floor, you need to ensure that your sub-floor is level. If your sub-floor isn’t level, you can have serious problems such as popping because of improper bonding due to insufficient contact between the sub-floor and wood plank.

If your sub-floor is uneven you will need to use a leveling compound before installation. Once the sub-floor is level, you can proceed with gluing your flooring using the manufacturer’s recommended adhesive. As the adhesive dries it shrinks, pulling your wood floor tighter to the sub-floor and giving a stronger attachment. Installing glue down hardwood flooring on concrete takes care. Make sure the concrete is dry and not wicking moisture from the ground to your wood, causing it to warp. Check the levelness of the concrete and fix areas that aren’t level and smooth. Consider an underlayment to help insulate against cold temperatures. Glue down installations are recommended for those who have experience working with the preparations methods that are described above. Be careful of fumes when working in an enclosed area too. Nail down installations are used when installing solid and engineered wood flooring. Solid wood flooring expands and contracts more than engineered and laminate flooring, so take care to acclimate the wood to your home’s interior before starting the installation.

Longer pieces should always be placed at entries and doorways if you are working with random lengths and the shorter pieces should be integrated throughout the floor. Nail down installations require that you place spacers around the perimeter of the room to allow the floor to expand and contract. When positioning your boards the groove side should be against the wall. Nails should go through the face of the boards and nails should be long enough to penetrate the sub floor by at least 1 inch. Nail down installations will require some basic carpentry skills and specialized tools such as a floor nailer, miter and jamb saws. This method of hardwood flooring installation is not recommended as a do-it-yourself project. Staple installations have become very popular and is mainly used with engineered wood flooring. The staple down method is used over plywood or wood sub-floors. Certain woods may require specific staple sizes to ensure a secure installation; your manufacturer can give you this information.