The page you requested was not found, and we have a fine guess why. If you typed the URL directly, please make sure the spelling is correct. If you clicked on a link to get here, the link is outdated. What can you do?Have no fear, help is near! There are many ways you can get back on track. Go back to the previous page. Use the search bar at the top of the page to search for your products. Follow these links to get you back on track!What are some Moen kitchen faucet repair instructions? Repair a leaking Moen kitchen faucet by replacing the cartridge. This fixes a faucet that is leaking at the handle or one that does not shut off. How do you remove a Moen kitchen faucet? Where can you find the model number on a Moen kitchen faucet? How do you use the Moen faucet repair cartridge? To replace a Moen faucet cartridge, start by shutting off the water supply to the faucet. Remove the handle cap, and locate the screw on the handle. Take the screw out, then pull the handle off.

Remove the clip by inserting the edge of a knife into the hole on the clip and moving the knife upwards. Pull the stem out with a pair of pliers. Where To Buy Snow Chains NzUse a Moen cartridge puller to replace the cartridge easily.Is Bamboo Flooring As Good As Hardwood To use the Moen cartridge puller, attach one end of the puller into the stem. Cheapest New Tires In San DiegoEnsure that the puller is tightly placed in the groves of the stem, then turn the puller from side to side to remove the cartridge. Once the cartridge is removed, install a new cartridge in place of the old one. Apply grease to the o-rings of the new stem, and put the clip back in place. Turn the water supply on. Confirm that the hot and cold water directions are working correctly.

If they're not, turn the center stem 180 degrees, then reassemble the faucet. How do you fix a kitchen faucet that has very low water pressure? Low water pressure in a kitchen faucet is fixed by cleaning the aerator and changing the cartridge. Sediment buildup is common in all faucets, so they shou... Common causes of problems with Moen faucets include scratched o-rings or grommets, a broken handle, a faulty rubber seal, a clogged cartridge or an obstruc... How do you replace a sprayer on a kitchen faucet? How does the laproscopic surgery repair a hernia? What tools are needed to repair a Kohler toilet tank? What are some unique master bathroom designs? How do you install a new bathtub? What are some tips for toilet wax ring replacement?DEAR TIM: Several weeks ago our whirlpool faucet water pressure and volume dropped to half while I was filling the whirlpool with water. The pressure and volume slowly returned to normal. At the same time, our kitchen faucet pressure and volume dropped even more than 50 percent.

It has not returned to normal and gets worse each day. All other faucets seem to work fine and the toilets fill quickly. What is wrong and is it expensive to correct? Patty J., Sterling, VA DEAR PATTY: Strange residential water pressure problems are far more common today than they were years ago. Part of the dilemma has to do with the internal design of many modern faucet valves and another part of the problem is directly related to natural resource conservation measures. Years ago many standard kitchen, bath and shower faucets had rubber and plastic washers that contacted a circular valve seat inside the faucet. As you opened a faucet the washer would pull away from the valve seat creating a very large pathway for water to flow through. In many faucets the pathway was so big, a small, round BB could easily pass though the faucet and into the sink or a glass of water. This older design allowed vast amounts of water to flow through a faucet and this is not a great thing when we have a growing population and limited fresh water supplies.

But many of today's modern faucets have washerless cartridges inside the body of the faucet. The modern cartridge replaces the older washer and valve seat design which controls water flow. The pathway through which water passes in these cartridges is much smaller than old faucets. Many of today's faucets also have an aerator at the end of the faucet. These devices are often made up of several small parts. If you take the aerator apart, you will discover extremely small holes in round disks made of plastic or metal. The water flowing from the faucet must pass through these tiny orifices. To meet federal and state guidelines to conserve water, many modern faucets and fixtures have flow restrictors that limit the amount of water that can pass through the faucet in a given amount of time. These restrictors often have tiny holes that limit the amount of water flow. I am convinced the drop in water volume and pressure at the two faucets was caused by small pieces of sediment or some other debris that clogged a passageway within the valve cartridge and/or the tiny orifices within the aerator and or a flow restrictor.

This is an extremely common problem for many homeowners. The sediment can form within a faucet or its parts depending upon the hardness of your water. Sediment also forms as a scale on the inside of municipal water supply pipes and the water lines inside your home. Pieces of this sediment can break off and be transported through the water lines as water moves towards a faucet. Small pieces of sand or rocks can enter a water system, especially those of people who use a private well. These can block the pathways within your faucets. These low water pressure and flow problems are very common just after a water main break in a municipal water system. Sand, dirt and other debris can enter municipal piping systems when a water main fractures. Once the water main is repaired, this debris is transported through the water system and can end up in your home. Small shavings of piping, soldering flux, sediment, etc. can also be carried through your own pipes when repairs are made to your plumbing system or new piping is added at your home.

Problems can also happen by simply turning on or off a main or secondary water control valve within your home by a plumber who might be installing a new faucet or performing a repair. If a city water main or water line inside your home is drained and then refilled with water, the incoming water can break off tremendous amounts of sediment and carry it through the water system. This happens when the surge of water rushes into the empty pipes creating a miniature tsunami of roiling water and sediment as the water fills the pipes. It is not expensive to correct the problem. The first thing I would look at are the aerators in any faucet that is giving you problems. Carefully remove the aerator and pay attention to how the different parts are assembled. Look at the parts, including the screening at the tip of the aerator, to ensure all parts are free of debris and all pathways are clear. Use tiny straight pins to open up any closed holes in these parts. You may have to soak the parts in warm, white vinegar overnight to removed caked, hard-water deposits that can build up within the aerator.

If, after reassembling the aerator, the water pressure and volume are still low, this means the problem is probably in the valve cartridge. The owner's manual that came with the faucet will show you how to remove and replace this common and inexpensive part. If you do not have the manual, try visiting the manufacturer's website for a technical bulletin showing you an exploded view of the faucet and its parts. To stop sediment from ending up inside the faucets in your home, it is best to open up an outside hose faucet or two to allow water to flow through them after you have completed a plumbing repair on your own home. These faucets often have the old-fashioned rubber or plastic washers. It is also a splendid idea to remove all faucet aerators before water is turned back on after a repair. I suggest turning on the main water valve very slowly after a home plumbing repair. Be sure to have the outdoor faucets open before you do this. This allows the pressure within the piping system to build slowly and a majority of sediment might be carried outdoors if the repair was made between the location of the hose faucet and the main water inlet to the home.