How do I resolve most common issues I am having with the Dual Flush Valve in my toilet? How to resolve the most common issues with the Duo Flush System Toilet Converter How do I install the Duo Flush System Toilet Converter? A) Please watch this installation video on installing the system: How Do I remove the Converter from inside the tank once I have all ready installed it? A) Gently rock the converter away from the overflow pipe and pull up. B) Unhook the cable box from the toilet handle – Push the button on the top of the box and pull the cable box away from the tank. The Full and Half flush closes immediately after I try a full or half flush: A) Change the dial settings on the top of the Converter. Changing the dials to a higher setting will allow for a longer flush. B) Raise the water level. Raising the water level so that it is ½ to ¼ inch below the overflow pipe will add head pressure and a longer flush period. C) If solutions A and B do not resolve the issue call Fluidmaster’s Technical Service Department 800-631-2011.

The toilet bowl does not completely flush out the paper:Cheapest Place To Buy Skid Steer Tires A) Change the dial settings on the top of the Converter. Multi-Pillow Back Sofa Slipcovers C) Check the Refill Tube to be sure it is pointed into the Overflow Pipe.Mobile Homes For Sale Ellenton Fl D) Disengage the Roller Clamp located on the Refill Tube so that the setting is on number 8 (flow is fully open). E)  If solutions A thru D do not resolve the issue call Fluidmaster’s Technical Service Department 800-631-2011. The Fill Valve turns on and Off (Ghost Flushing) and turns the toilet on through the day: A) Check the Refill Tube to be sure it is above the overflow pipe and hooked to the Refill Tube Clip.

If the tube is inside the overflow pipe pull it out and attach to Overflow Pipe using a Refill Clip. B) Clean Drain Seat – Pull off converter from inside the tank drain and clean both the seat and the rubber seal located at the bottom of the converter.  Replace converter when clean. C) Reset Angled Seat Adaptor. Pull converter off the drain and remove the angled seat adaptor, once removed turn it upside down to locate the sealing putty. Spread the putty around the adaptor base evenly. Replace adaptor and replace Converter back onto drain. D) If solutions A thru C do not resolve the issue or you need a Refill Clip call Fluidmaster’s Technical Service Department 800-631-2011. For questions that are not listed here please contact Fluidmaster’s Technical Service Department: Hours: 5:30 AM to 5:00 PM Monday thru Friday Solutions for a toilet fill valve that will not turn off Adjusting the water level in the toilet bowl and setting the refill rate

Fix your most common toilet problems fast and easy Solutions for a Weak or Incomplete Flush (toilet bowl does not clear) after installing a Fluidmaster Toilet Repair Kit Solutions for a toilet that ghost flushes (toilet that turns on by itself)Ten Common Toilet Problems and the Solutions You could have a first generation 1.6 gallon flush toilet that is destined to failure. Look inside the tank for a manufacture date stamped in the clay. If it was made during the time period from January 1, 1994 to mid-1997, this could be the problem. No matter what you do, it will not flush right. If the toilet was made before 1994, hard water deposits in the syphon jet hole or the angled bowl rim swirl holes may be the source of your frustration. You can try to clean them out with wood sticks and oversized toothpicks, but a muriatic acid wash will really do the job. Mix one part acid to 10 parts water. Using a funnel, carefully pour one half of this solution down the overflow tube in the toilet tank.

You should immediately hear fizzing and such. BE CAREFUL of the fumes! Run the bath fan, open a window. DO NOT splash this solution on you, in your eyes, on your clothes, on the carpet, etc. It will not hurt the toilet at all. If you have a septic system, do not do this! The only way you can clean your toilet is to disassemble it and do this process outdoors. Let the acid work for about 30 minutes. Pour the remainder of the solution down the overflow tube. After an additional 30 minutes, flush the toilet. You should see an improvement. The flapper valve may be waterlogged and dropping too fast. Observe the flapper valve during a flush. It should stay up until about 80 percent or more of the water has drained from the tank. If it drops sooner, install a new flapper. This is really a phantom filler, as the toilet tank fills with water as if it was just flushed. It simply means that the tank is leaking water. The food coloring dye test will confirm this. Add food dye to the tank after all water has stopped running into the tank.

After 5 or 10 minutes, look at the bowl water to see if it is colored. If it is, the flapper is not sealing completely. Time for a new one! You flush the toilet and all is well. After a period of time, a significant amount of water has left the bowl. Two things may be wrong. Water could be slowly siphoned from the bowl by a partial clog of toilet paper up in the colon of the bowl. You can demonstrate this phenomenon by filling a small soup bowl with water and putting it in the center of a cooking jelly pan. Drape a strip of paper towel from the bottom of the bowl, over the bowl edge and into the jelly pan. Watch what gravity and capillary attraction does in several hours. The bowl will be nearly empty. To see if your toilet has a rag, toilet paper, or something else causing the drainage, empty the bowl of water and then use a flashlight and a mirror to look up inside the colon of the toilet. In rare cases, the bowl may actually have a crack in the interior colon or piping of the bowl.

This problem can only be solved by installing a new bowl. The water level in the tank may be set too high. Lower the level and look for improvement. You must have an old technology ball cock valve with a ball float on the end of a rod. As the ball floats higher it begins to slowly close the water fill valve. This can cause vibrations and all sorts of noise. Toilet tank fill valves that stay wide open until the tank is filled have been around for over 20 years. They are wonderful and they are inexpensive. I use the Fluidmaster valve. Get the best one, not the economy model. This problem may be a partially closed shut off valve under the tank. A previous owner or a plumber may have restricted the flow of water into the tank for some reason. After the tank has filled, you hear dripping. Then several minutes later, the tank partially fills with water and the dripping starts again. Then the tank fills and so on and so forth. This problem can be a syphon problem caused by someone who installed a new tank fill valve.

There is a small flexible tube that runs from the bottom of the valve to the top of the toilet overflow tube. As the tank fills, water is also sent through this tube. It is used to refill the toilet bowl since it lost its water during the flush. If this tube drops down inside the overflow tube, it can, in some instances, syphon water from the tank. New toilet fill valves often have a clip that attaches to the top of the overflow tube and points the water flow down into the tube without actually having the tube enter the tube. The toilet could have a partial clog or the actual clog could be downstream from the toilet. Fill a 5 gallon bucket of water and dump it into the toilet as fast as possible with minimum splashing. If the flush is more vigorous, then it is probably not a clog. If water backs up into the bowl and drains slowly, it is a clog. Suction Sounds in the Tub and Sink You flush the toilet and gurgling sounds come from your tub and/or bath sink. This means the toilet vent pipe is clogged or partially clogged.