Metal stoppers stuck in a sink drain are easily fixed. A stuck metal sink stopper prevents water from draining out of your sink, which stops you from using the sink until it is removed. If the stopper is stuck and simply pulling it does not remove it, there are a few small tricks you can try to dislodge the stopper without taking your sink apart. If it still cannot be removed, you will have to remove some parts to push the stopper up and free it from the drain. Twist the stopper and lift it up if it has a small knob in the center. This may break the seal holding the stopper in place, allowing you to remove it. If the stopper does not have a knob, proceed to the next step. Place a suction cup on top of a metal sink stopper that does not have a knob, and push down on the suction cup to create a seal on the top of the stopper. Lift up to remove the stopper with the suction cup. If the metal sink stopper is still stuck, proceed. Remove the pivot rod nut under the sink by turning it counterclockwise with a pair of pliers to remove the pivot rod.

The pivot rod is a small rod extending from the sink’s drain beneath the sink, held in place by the pivot rod nut. Remove the pivot rod and pull the stopper up and out of the drain. Turn the stopper so that the hole in the bottom faces the pivot rod’s position in the drain, and place the metal sink stopper back into the drain. Reinstall the pivot rod and tighten the pivot rod nut to secure it. Things You Will Need Suction cup Pliers References YouTube: Removing a Stuck Sink StopperHome Tips: How to Fix a Bathtub or Sink Pop-up Stopper Photo Credits Comstock/Comstock/Getty Images Suggest a CorrectionDo it Stainless Steel Basket Strainer Stopper With Threaded Post Sinks and tubs whisk away a lot of stuff, including dirt, soap, shampoo, hair, dead skin — a lot of material that can build up in the drain. While we may be quick to grab a drain cleaner or try a plunger when water won't go down, sometimes a simple cleaning out can do the trick. Feed a drain snake (if you don't have one, try straightening a wire clothes hanger) a few inches past the stopper, twirl it around and slowly pull it out.

This will be easier if you can remove the stopper. There's a good chance you'll snag a clump of hair and gunk. Grey Drape CardiganKeep doing this a few times until the water drains and you can't remove anything else. Hybrid Wolf Puppies For Sale In FloridaNow's a good time to follow up with a drain cleaner or a simple combination of baking soda and vinegar, followed by very hot, but not boiling, water.Ways To Hang Curtains Without Nails The toilet handle has one job: to open the flapper and allow the tank water to release and flush out the contents of the bowl via pressure. If the handle breaks, no flush. A handle can fail outside of the tank, where it simply snaps off, or inside, where the arm connected to the flapper chain breaks.

The chain can also slip off the arm, which will give the impression that the handle is broken. Check the chain first, and simply slide it back on the arm and flush. If the arm breaks, you'll need to pull the chain to open the flapper to flush. If the handle breaks on the inside, simply lift the arm to flush. Handle replacement parts are inexpensive and easy to find in the plumbing department at a home center. In your mind you know you won't do it, but some neuron misfires, your hand twitches or you bump your arm, and KERPLUNK! Your cellphone lands in the toilet. It's actually not an uncommon occurrence that a phone lands in water, although a toilet may not be quite as common (at least admittedly). Don't freak out, but act like a ninja and snatch it out of the bowl as quickly as possible. Pat it dry with a paper towel, then remove the battery and dry the battery and battery recess as much as possible. If away from home, wrap them separately in an unused and dry paper towel. As soon as you can, place the phone and battery in a bowl or resealable plastic bag with uncooked rice, enough to completely cover them.

Make sure the phone and battery do not touch, and allow them to sit in the rice for a full day. Remove any dust from the rice before reassembling the phone and battery. You can feel helpless watching the toilet bowl overflow, but you can stop it quickly. Reach for the water cutoff valve (usually behind or slightly off center of the toilet near the floor) and turn it off (righty-tighty).This will immediately stop water from refilling into the tank, which in turn goes into the bowl. If it's not overflowing but slowly rising, you can reach into the tank and lift the ballcock (float) to horizontal, which will stop the valve from allowing more water into the tank. This will give the bowl time to drain. A clogged toilet leads to the aforementioned overflow problem, but it also can also create a slow drain. It's a nasty job, but one that requires a few basic steps. Grab the go-to tool: the plunger. The key to getting the plunger to do its job is getting good coverage over the drain hole at the bottom of the bowl, which helps facilitate the suction and force action.

The prototypical plunger isn't the best at doing this. Newer designs with a smaller mouth actually are better. It may take several tries, but plunging usually does the trick. If not, try pouring really hot, but not boiling, water into the bowl. This can sometimes weaken what's clogging the drain. Follow this with more plunging. Your last option, if all else fails, is using a drain snake. A wee wobble while sitting on the porcelain throne is not only annoying, but also a potential problem. A lot of movement and tilting could ruin the wax ring's seal at the bottom of the toilet, which will eventually lead to a leak from flushed water. This can be a simple fix. First try tightening the nuts on the bolts at the floor, making sure to not over-tighten the nuts, thus cracking the toilet base. If that doesn't fix it, you'll need to remove the toilet because it’s likely the bolt heads have come loose from the drain flange or have broken. This is a good time to replace the bolts (and nuts), as well as the wax ring.